Connect with us

Business

7 Major Safety Tips when Working at Heights

Published

on

7 Major Safety Tips when Working at Heights

Whether you are working at heights once in a while or every day, your safety focus during those times is of crucial importance. This takes just one mistake to turn a routine task into a fatality. This is obvious that falls are debilitating. Falls from a certain height is often deadly. If you own a workshop or factory where the workers are required to work at a height very often, then you should necessarily train the workers with working at heights course to maintain adequate safety and to prevent any unfortunate accident in the workplace.

What is Working at Height?

Working at height course refers to any work which is above the ground or even below the ground in which a person has a chance to fall and injure themselves if no proper precautions are taken. There are chances that you can fall off the ladder or off the roof’s edge or even through any probable opening on the floor. In the general industry, fall protection is required at 4 feet which is above a lower level. Here are a few important safety tips to be necessarily considered if the employees work at heights. Here are a few crucial safety tips which should be necessarily considered if the workers are working at heights. These following points are usually included in working at heights course.

 

7 Major Safety Tips when Working at Heights

 

  • Usage of Railing

    Whenever it is possible, the railing should be used preferably. Passive protection is indeed the easiest way for keeping the workers safe and also to adhere to the compliances which keep the workers safe while working at heights. There are railing systems available for almost every type of rooftops like the non-penetrating railing for low-slope or flat roofs. Also, pre-fabricated railings can be permanently affixed or portable in order to suit the needs.

  • Selection of The Proper PPE

    In case you are going to use Personal Fall Arrest Systems (PFAS), you necessarily need to enquire that you choose the proper equipment to resist the accident. All the full-body harnesses which meet ANSI standards will perform the same, despite the cost.

  • Inspecting Your PPE

    The workers can use all the equipment which they require but they need to be necessarily inspected at regular intervals or else there are possibilities of failure.

 

 

Suggested Article

Rope Access – A Greener Approach to hard to reach places

Rope Access - A Greener Approach to hard to reach places

 

 

 

 

  • Ensuring That You Understand the Fall Distance

    You can opt to wear all the fall protection equipment in the world but if this allows you to hit the lower level before it engages, then it is completely pointless. This may sound like something of “common sense” but you would be surprised at how many people do not deem to have that sense of working at heights course.

  • Ensuring the Selection of Acceptable Anchor Points

    If you were to pick a particular construction site at random and inspect what anchor points, they are using, you might end up assuming that there are no rules regarding this. A PVC pipe or decorative steel can’t be considered as anchors.

  • Ensuring That You Select the Best Means of Working at Heights

    Just as the harnesses are not one-size-fits-all, they are also not considered as fall protection solutions. A scaffold is considered as the best solution to work at heights and you can certainly be able to equip them with rails and make your fall protection easier to address.

  • Using Ladders Properly

    You should not assume that a ladder that you have retained can be used for multiple purposes. There are specialized ladders for various purposes which would keep the workers safe from accidents. So, the ladders have to be chosen appropriately.

 

Conclusion

The above pointers are major contents of the working at heights course and this makes the management and workers in a manufacturing unit aware of the safety norms while working at height.

 

 

Read more Business related stories in The Weekly Trends magazine.

 

 

 

Alyssa Moylan is an ordinary woman from Australia, a writer by day and a reader by night. She writes on various topics like home improvement, business, lifestyle, health, travel and fashion. She likes to think of ways on how to solve daily life problems of people.

Continue Reading
1 Comment

1 Comment

  1. Pingback: Safety and Awareness tips for working in Confined Space - The Weekly Trends

Leave a Reply

Your email address will not be published. Required fields are marked *

Support Us!

Write for Us

The Weekly Trends

The Weekly Trends

Facebook

Trending